Demo. Aeroline MRO is a fictional business, made to show what 3D Viewer Premium can do.How this page is built

Aeroline MRO

Jet engines off the wing, inspected, and back in service.

We overhaul turbofans for regional and charter operators, and restore heritage airframes. Every work package starts with the engine in 3D, so you can see what we will open and why.

Turbofan and transport stand

  • 4.1 m on its stand
  • 22 fan blades
  • 15 rotor stages

Gas path

Follow the air through the engine.

The cowls are cut away so you can see inside. Tap a number and the camera moves to that part of the gas path; the reset button brings the whole engine back.

  1. IntakeAir enters through a smooth aluminium lip. We check it for dents and the acoustic lining behind it for delamination.
  2. FanTwenty-two wide-chord titanium blades move most of the air. Each one is measured at the leading edge.
  3. CombustorAn annular chamber with twenty fuel nozzles. Its liner is where heat damage shows up first.
  4. Turbine and exhaustTwo high-pressure and four low-pressure stages, then the exhaust plug. The blades here run hottest.

Shop visit

What we check on a shop visit.

Six inspection points, each pinned where the work happens. Tap a number to read what we look for, or the play pin for a short clip of the fan.

Pin 1

Fan cowl

Latches, hinges and the lightning-strike mesh are checked before the cowl comes off.

Pin 2

Compressor

Nine high-pressure stages. A borescope goes in through the inspection ports between them.

Pin 3

Combustor liner

We look for cracks and burn-through around the fuel nozzles and map them for the report.

Pin 4

Turbine blades

Coating loss and tip rub are measured against the limits in the engine manual.

Pin 5

Exhaust plug

Checked for cracks and distortion. It is one of the few parts you can see on the wing.

Play pin

Fan blades

We spin the fan by hand and look at every blade. This clip is rendered from the model on this page.

Hangar fit

Will it fit through the hangar door?

Before a heritage airframe arrives, we check it against our bays. This is a reproduction of the 1903 Wright Flyer at its real size, with the measurements drawn on as you turn it.

  • 12.3 mwingspan
  • 6.4 mlong
  • 2.8 mhigh
  • Bay 1: 16 m door, for engines and regional airframes.
  • Bay 2: 14 m door, for heritage work and long restorations.

Heritage airframes

Airframes in 3D, before they arrive.

A restoration quote starts with a survey. These two public models show what a client sees first: the whole airframe, ready to turn and zoom. Pick one from the strip.

Wright Flyer: a 3D reproduction from the Smithsonian’s open-access scan. X-57: a public NASA model of an electric research aircraft. Neither institution endorses this page, and we have not worked on either aircraft.

Request a quote

Send us the engine type and its hours.

We reply with a work scope and a slot in the shop. On a real MRO website, your quote form goes here; this demo does not take requests.

  • Engine type and serial number
  • Hours and cycles since last shop visit
  • Your quote form

Behind the demo

How this page is built

Every 3D section on this page is the standard 3D Viewer block. The settings below use the control names you will find in the plugin.

SectionWhat it usesSettings
HeroModel animation, auto-rotate, HDR lightingAutoplay on, animation Fan spin. Auto Rotate on, 2 s delay. Environment Image = hangar HDR, Exposure 1.05
Gas path4 Waypoint hotspots (camera views)Type: Waypoint. Pin Icon: Number. Each pin stores orbit, target and FOV. Reset View button
Inspection5 Info hotspots, 1 Video hotspotStyle: Hover Popup Card. Video hotspot plays an MP4 from the media library in a popup
Hangar fitReal-world dimensions in the viewerDimensions Always, m. The model is at real size, so no Real Size override is needed
Airframes2 models in one viewerMultiple models, thumbnails Left
Page designFonts, colours, header and footerPage CSS only. The viewer buttons and pins are restyled with CSS; the plugin settings are unchanged

What this page does not do

  • The turbofan is a generic engine made for this demo. It is not a real engine type, and its parts are simplified.
  • The camera views move the camera only; there is no guided sequence.
  • The fan clip is rendered from the model, not filmed in a shop.
  • There is no quote form, and nothing on this page is maintenance data.
  • The measurements are the whole model’s outer box and hide once AR starts.

Model credits

  • Turbofan and transport stand: made by bPlugins for this demo, CC0.
  • 1903 Wright Flyer: Smithsonian National Air and Space Museum 3D scan, CC0, via the Smithsonian 3D API. Shown as a reproduction.
  • X-57 Maxwell: NASA 3D Resources (github.com/nasa/NASA-3D-Resources), free to use. Reduced and repainted plain white.
  • Hangar lighting: “Aircraft Workshop 01” HDRI by Poly Haven, CC0.
  • Credit to NASA and the Smithsonian does not mean they endorse this page or the plugin.
Scroll to Top